6706 Fuel Injector Rail Assembly Remover Tool for V6 & 4 Cylinder, Compatible with 2007-2014 GM Cadillac Saturn Pontiac Chevrolet Direct Injection Engines, Alternative to EN-49248
$31.50
Application:Fits for Buick Envision model years 2016 and 2017. Fits for Buick LaCrosse Regal model years 2011, 2012, 2013, 2014, 2016 and 2017. Fits for Buick Verano model years 2012, 2013, 2014, 2016 and 2017. Fits for Cadillac ATS model years 2013, 2014, 2016, and 2017. Fits for Cadillac CT6 Escalade ESV model years 2016 and 2017. Fits for Cadillac CTS model years 2011, 2012, 2013, 2014, 2016 and 2017. Fits for Cadillac Escalade model years 2015, 2016 and 2017. Fits for Cadillac SRX model years 2011, 2012, 2013, 2014 and 2016. Fits for Cadillac XT5 model year 2017. Fits for Cadillac XTS model years 2013, 2016 and 2017. Fits for Chevy Camaro model years 2012, 2013, 2014, 2016 and 2017. Fits for Chevy Caprice model years 2011, 2012, 2013 and 2014. Fits for Chevy Caprice PPV Orlando model years 2012, 2016 and 2017. Fits for Chevy Captiva Captiva Sport model year 2012. Fits for Chevy Cheyenne Colorado S10 TrailBlazer model years 2016 and 2017. Fits for Chevy Corvette model years 2014, 2016 and 2017. Fits for Chevy Equinox model years 2011, 2012, 2013, 2014, 2016 and 2017. Fits for Chevy Impala model years 2012, 2013, 2014, 2015, 2016 and 2017. Fits for Chevy Impala Limited and Malibu Limited model year 2016. Fits for Chevy Lumina model years 2011 and 2012. Fits for Chevy Malibu model years 2013, 2014, 2016 and 2017. Fits for Chevy Silverado model years 2014, 2015, 2016 and 2017. Fits for Chevy Suburban and Tahoe model years 2015, 2016 and 2017. Fits for GMC Acadia model year 2017. Fits for GMC Canyon and Yukon XL model years 2016 and 2017. Fits for GMC Sierra model years 2014, 2015, 2016 and 2017. Fits for GMC Terrain model years 2011, 2012, 2013, 2014, 2016 and 2017. Fits for GMC Yukon model years 2015, 2016 and 2017. Fits for Holden Colorado 7 model year 2016.  Essential Handy Tools Set: The fuel rail and injector assembly used for the Hitachi SIDI system on 2010 LF1 3.6L V6 and LAF 2.0L ECOTEC has two seals on each injector, and these seals are installed with very tight tolerances. Once the engine has been run, injector and rail removal is very difficult, and the assembly must be removed as straight as possible to prevent the chance of damaging an injector bore in the cylinder head, or to the mount assembly. Each mount assembly contains an isolator, and cannot have any force applied to the mount for removal.  Powerful functions: Similar to EN-49248 and compatible with OTC 6706. The tools kit installs in place of the mounting bolts and reaches under the injector rail near each mount location, helps properly remove the direct injection fuel rail. The hand wheels on EN-49248 at each mount location are tightened evenly to un-seat all injectors evenly, preventing damage to the injectors, cylinder head, and rail mount assemblies. Perfectly fits for 2007 - 2014 General Motors Cadillac Saturn Pontiac Chevrolet direct injection engines. Application for 4.3L 3.6L 3.0L GDI V6, 2.5L 2.4L 2.0L GDI I-4. (Note: If you are working on a 5.3L or 6.2L you will need a quantity of 2 sets.) Usage Guide: Step 1. Remove the fuel injection fuel rail noise shield. Disconnect the electrical harness from the fuel rail harness connection. Disconnect all 4-fuel injector electrical connections. Remove the fuel rail assembly retaining bolts. Note: Use care to avoid contact with the fuel rail harness during special tool installation and fuel rail removal. Step 2. Install EN-49248studs (1) into the 2 center fuel rail assembly retaining bolt locations. Tighten the studs to 22-Y(16-lb-ft). Install EN-49248 remover-(2) onto each stud, and engage the hooks to the fuel rail. Install the nuts-(3) retaining there mover onto the studs and tighten until snug. Step 3. Note: EN-49248 will assist in the proper removal of the fuel rail assembly. Ensure that the following conditions are met: Turn the handles simultaneously in order to pull the fuel rail straight out along the fuel injector axis. DO NOT twist when pulling out on the fuel rail and injector assembly. Using EN-49248 remover, remove the fuel rail assembly-(1).
Features & detailsFeatures
Product information
Additional InformationHave a question?Find answers in product info, Q&As, reviews Have a question?Top results Customer Q&A Customer Reviews Product info Post question There was a problem completing your request. Please try your search again later. Brief content visible, double tap to read full content.Full content visible, double tap to read brief content.VideosPage 1 of 1Start OverPage 1 of 1
  Customer Review: EN-49248 Injector Rail Assembly Remover Tool 6706See full reviewEarns CommissionsEarns Commissions00:00-00:00  Shop  Share  More videos No related products
Brief content visible, double tap to read full content.Full content visible, double tap to read brief content.
Customer QuestionsThere was a problem completing your request. Please try again later. Don''t see the answer you''re looking for? Post failedError posting question. Please try again. There are 0 customer reviews and 4 customer ratings.How customer reviews and ratings workCustomer Reviews, including Product Star Ratings help customers to learn more about the product and decide whether it is the right product for them.Learn more how customers reviews work on Amazon Brief content visible, double tap to read full content.Full content visible, double tap to read brief content. Brief content visible, double tap to read full content.Full content visible, double tap to read brief content. Brief content visible, double tap to read full content.Full content visible, double tap to read brief content.You are herea-link-normal" href="/gp/site-directory">Department Automotive Replacement Parts Fuel System Fuel Injection Fuel Injectors & Parts Fuel Injectors |
